rapidfuseallpurpose.dap.comRapidFuse All Purpose – Fast Curing All Purpose Adhesive

You are using an outdated browser. Please upgrade your browser to improve your experience. Toggle navigation RapidFuse All Purpose About Key Features Helpful Tips FAQ Reviews RapidFuse All Purpose Better Than Super Glue* Tougher Than Polyurethane* Bonds Virtually Everything Where to Buy All Purpose Adhesive Plastic Primer Kit Key Features Product 1 Sets in 30 Seconds – no clamps required Cures in 30 Minutes 40% stronger than polyurethane glue* No foam, no mess & dries clear 2X more durable than super glues* Interior/Exterior Use Video Title 1 Video Title 2 Product Name 2 Bonds Everything - Including all plastics Easily fuse hard-to-bond plastics with plastic primer Sets in 30 Seconds – Cures in 30 Minutes 10X tougher than competition** Interior/Exterior Use × Video Title 1 Close × Video Title 2 Close Helpful Tips 1 To get a good bond, make sure the surface is clean and dry before applying. 2 Do not use too much - just enough to cover the area you intend to bond with a thin coat of adhesive. 3 Squeeze the two substrates you are bonding together tightly for 30 seconds. Wipe away any excess or “squeeze out” with a dry paper towel. 4 If fusing plastics be sure to use plastic primer marker on all plastic surfaces being fused and wait 60 seconds prior to applying adhesive. 5 If you didn’t get the placement right to start, you can pull the two materials apart and realign them before applying another 30 seconds of pressure. 6 Set your repair down and walk away while it cures in 30 minutes. Bonds Virtually Everything to Anything DAP RapidFuse All Purpose -- Vase × DAP RapidFuse All Purpose -- Vase Close DAP RapidFuse All Purpose -- Multi-tool × DAP RapidFuse All Purpose -- Multi-tool Close Fast Curing All Purpose Adhesive Frequently Asked Questions How much should I use? Just enough to cover the area you intend to bond with a thin coat of adhesive. Use less on non-porous substrates like metal, glass or plastic. Use slightly more on porous substrates like wood or ceramics. Apply glue to only one surface, not both sides. You can use the two surface you are joining or the precision tip applicator of the bottle to spread the adhesive, but make sure when you press the substrates together to remove any excess. How do I fuse plastics? When bonding plastics - be sure to use the primer marker on all plastic edges only and allow to dry 1 minute prior to applying adhesive. What if I can't make the two surfaces touch? The two surfaces have to touch with pressure for 30 seconds. If you can’t make the materials touch, you will not get a good bond. Try using a clamp if you can’t keep the substrates together with just your hands. Leave the clamp on for at least 5 minutes to make sure you get a good bond, or for a full 30 minutes for a cured repair. How can it set in 30 seconds and reposition up to 3 minutes? RapidFuse will set after 30 seconds of strong pressure at which point you can set your repair down and walk away while it cures in 30 minutes. However, if you didn’t get the placement right to start you can pull the two materials apart and realign them before applying another 30 seconds of pressure to set it. What does up to 3 minutes of reposition time mean? The reposition time will vary by substrate. A non-porous substrate like metal or glass will set much faster and give a shorter reposition time. Porous substrates like wood can be repositioned for 3 minutes. On materials like metal, glass and ceramics, don’t apply pressure for 30 seconds until you have the lineup of your materials perfect. RapidFuse adhesive didn’t cure in 30 minutes. What went wrong? If RapidFuse adhesive doesn’t cure in 30 minutes, then it's likely you over-applied. Simply get a dry paper towel and remove the excess adhesive so it can cure properly and give it another 30 minutes. A good rule of thumb is if it’s shiny – then it’s still wet. How do I get RapidFuse off my skin? Use Acetone nail polish remover to get cured RapidFuse off your skin. Make sure it is Acetone nail polish remover. The non-acetone stuff won’t work. Wash your hands first to remove any un-cured adhesive with soap and water. Then wipe with an acetone soaked cotton pad. Do not try to pull or peel RapidFuse off. Reviews This website uses cookies and other tracking technologies (also known as pixels or beacons) to aid your experience (such as viewing videos), as well as “performance cookies” to analyze your use of this website and to assist with marketing efforts. If you click the "Accept All Cookies" button or continue navigating the website, you agree to having those first and third-party cookies set on your device. If you do not wish to accept cookies from this website, you can choose to not allow cookies from this website by updating your browser preferences. For more information on how we use Cookies, please read our Privacy Policy . Accept All Cookies RapidFuse All Purpose RapidFuse All Purpose, Fast Curing All Purpose Adhesive About Key Features Helpful Tips FAQ Reviews * 40% Stronger than polyurethane glues based on averaging strength on ABS plastic, polycarbonate, white oak, rubber and steel. 2X more durable than traditional cyanoacrylates. **As compared to the leading two part plastic repair system. Terms Of Use & Privacy Policy Contact Us Dealer Info Invention Submission California Supply Chain Disclosure © 2020 DAP Products Inc. ')...